PEDROLLO 2CR m 80 WATER PUMP withBRIO TANK PRESSURE SENSING CONTROLLER

PEDROLLO 2CR m 80 WATER PUMP withBRIO TANK PRESSURE SENSING CONTROLLER
PEDROLLO 2CR m 80 WATER PUMP withBRIO TANK PRESSURE SENSING CONTROLLER
PEDROLLO 2CR m 80 WATER PUMP withBRIO TANK PRESSURE SENSING CONTROLLER
PEDROLLO 2CR m 80 WATER PUMP withBRIO TANK PRESSURE SENSING CONTROLLER
PEDROLLO 2CR m 80 WATER PUMP withBRIO TANK PRESSURE SENSING CONTROLLER

PEDROLLO 2CR m 80 WATER PUMP withBRIO TANK PRESSURE SENSING CONTROLLER

A Pedrollo CR2 m80 water pump complete with Brio Tank pressure sensing pump controller. The Pedrollo 2CR80 Series water pump which is suitable for use with clean water and liquids that are not chemically aggressive towards the materials from which the pump is made. As a result of their quietness the Pedrollo 2CR80 series pumps are widely used in domestic applications such as the distribution of water in combination with small and medium sized pressure sets, and for the irrigation of gardens and allotments, etc. Installation needs to be undertaken in well ventilated closed areas or anyway protected from bad weather. Irrigation pumps, water supply systems, pressure systems.

Flow rate up to 130 l/min (7,8 m³/h) Head up to 67 m. Ambient Temperature to +40 °C Manometric suction lift up to 7 m Liquid temperature: between -10 °C and +60 °C for 2-5CR between -10 °C and +40 °C for 2-5CR X Max. Working pressure 7 bar Continuous service S1.

BRIO TANK PRESSURE SENSING PUMP CONTROLLER. Tank Version Includes 0.4ltr Pressure Vessel. The BRIO is a fixed pressure sensing controller with dry run protection. Designed to automate the operation of an electric pump, the BRIO TANK has the ability to sense a drop in pressure in the system (opening a tap or valve).

The pump controller will turn off the pump when the tap valve is closed and the system is re-pressurised. (Starts and stops the pump with the opening and closing of the taps). The BRIO can be used in conjunction with shower pumps in installations where there is a negative head otherwise known as universal head (when the shower head is above the water level in the cold water storage tank), and also where the pumps are supplying several outlets at once e. Body jets or rain bars, or domestic water supplies (toilets, taps, washing machines). The BRIO comes complete with a pressure gauge which allows the starting pressure value and system pressure to be easily checked.

The unit will also protect the pump from dry running if the water supply should fail. The TANK version also has 0.4ltr pressure vessel attached which negates the need for a separate vessel in certain situations. BRIO controllers are suitable for use in pairs to operate shower pumps on hot (max 65°C) and cold supplies, subject to the maximum electric load (12 amps) not being exceeded.

The BRIO is designed for use on clean water. If there is a possibility of sediment, a suitable filter should be installed before the unit. It automatizes the start and stop operations of single-phase electric pumps up to 2HP It replaces completely the traditional water system set up consisting on pressure switch and pressure tank It starts the electric pump after a pressure decrease (taps opening) and stops it when the fluid flow interrupts at the maximum pressure level of the electric pump (taps closing) A small 0,4 l water tank is integrated and it prevents unlikely frequent start and stop of the pump in case of small request of water and in case of leakages on the installation Replaceable EPDM bladder of the pressure tank Adjustable pre-charge pressure (factory setting 1 bar) of the pressure tank Integrated pressure gauge Protects against dry running and water hammering Standard 1 M hydraulic connections Installation in any position both vertical and horizontal according to the flow direction Electronic printed circuit board housed in a waterproof compartment protecting against water condensation No need of maintenance. Power Supply: 230V 50 or 60 Hz.

Voltage tolerance +/- 10% Max. Switching Current: 12 Amps Max. Motor Size: 2 HP Max.

Total Pressure: 10 Bar Max. Liquid Temperature: 35°C Connections: 1 BSP male Protection: IP65 Pressure Gauge: 40mm dia 0-12 Bar. We have other laboratory equipment available. See our other listings or message me with specific enquiries/requirements. CONDITION All very good condition as pictured and in full working order. Peaktech UK Ltd Company No 8127946. The item "PEDROLLO 2CR m 80 WATER PUMP withBRIO TANK PRESSURE SENSING CONTROLLER" is in sale since Thursday, November 4, 2021. This item is in the category "Business, Office & Industrial\Hydraulics, Pneumatics, Pumps & Plumbing\Pumps & Pump Accessories\Circulator Pumps". The seller is "peaktech_uk" and is located in High Peak.

This item can be shipped to United Kingdom, United States, European Union member countries, Canada.


PEDROLLO 2CR m 80 WATER PUMP withBRIO TANK PRESSURE SENSING CONTROLLER